man in blue with helmet

Edition 02/2019

Article and compact news

Our AERZEN customer journal "AERZEN com.press" will provide you with detailed information at regular intervals about our company, our products and application solutions.

Article

Size actually matters

Amount of air in the limestone production

David Salazar, Aerzen Americas Application Manager, Cement - Lime – Concrete, writes about selecting the right technology and machine size for fuel conveying, combustion air and air cooling systems to optimise fuel efficiency in the kiln for lime production plants.

AERZEN Delta Hybrid in a lime plant

According to the data available from the USGS (U.S. Geological Survey), in 2018, the quicklime and hydrate lime market value in the Americas exceed the USD 3 Billion and an estimated of 32 million tons were produced all over the region from over 120 production plants located from Canada to Argentina, the market growth expectations worldwide are about 7.5%, and the Americas expects to reach a constant CAGR of 7% from 2018 to 2022, mainly driven by the need of improved processes in the mining industry, sugar cane market by the increased demand of biofuels and the industrialisation for wastewater treatment facilities in Latin American Countries. These good market expectations for the near future require serious process optimisations in the production facilities to look for the best fuel efficiency in the kiln process. The efficiency in the burning process is closely related to the availability of certain types of fuel and the proper selection of the fuel conveying, combustion air and cooling air technologies that includes low pressure oil free rotary lobe compressors and turbo blowers.

Kiln technologies

Vertical vs rotary kiln analysis, AERZEN

Currently in the limestone production processes, there are two main kiln technologies used: vertical kilns and rotary kiln systems. Both technologies require a large amount of low pressure oil free air for fuel conveying and cooling processes to guarantee the proper quality of the calcium oxide, according to a specific research on lime production process in the USA from RTI (Research Triangle Institute). Vertical kilns are the preferred technology for lime producers as less capital investment is required, and the fuel efficiency is greater. However, in the U.S., vertical kilns have been largely replaced by rotary kiln systems, mainly because they require less labor and have the highest output by reducing the amount of spalls. A summarised analysis of the two technologies is shown in the table.

Air supply for the kiln

As shown in table, the amount of air required for both vertical and rotary kiln in the combustion process is large enough to consider it as critical application for the production process. AERZEN application specialists have identified some common improving opportunities at different plant locations that involve the following main aspects:

  • Appropriate selection and design of the machine that provides the combustion air to efficiently burn the fuel. In total, AERZEN offers with positive displacement blowers, rotary lobe compressors, screw compressors and turbo blowers, an extensive range of products and technologies in order to be able to offer tailor-made process air solutions for the most diverse requirements.
  • Design of the pipe diameter through which the air for the cooling lances (vertical kilns) flows. There is the danger that the air speed is too low, which can lead to clogging of the lances.
  • Initial investment for the low pressure air compressors, without considering the TCO for the project, which in the medium term may lead to a reduction of MTBR and an increase of the total cost of ownership.

Application specialists

AERZEN has a rich history of devising low-pressure solutions that consider important and flexible performance parameters and requirements in various production processes. Contact your local application specialist. For the Americas, forward your requests to: david.salazar@aerzen.com

Compact news

AERZEN Technology at the L‘Aquarium in Barcelona

The spectacular Oceanario de L’Aquarium in Barcelona is considered the largest and most species-rich aquarium in Europe. With a diameter of 36 metres and a depth of 5 metres, it holds approximately 4 million litres of water. A few months ago, an AERZEN Delta Blower package was put into operation in the L’Aquarium. A large team of highly qualified professionals and cutting-edge technology enables to guarantee the health and wellbeing of over 11,000 animals at the L’Aquarium.

Around 6 million litres of seawater is needed to fill the 21 aquariums. This water is supplied continuously by means of controlled extraction in wells arranged specifically for this purpose. A sophisticated water purification system enables operation in a semi-closed cycle. Purification and filtration are required for a number of reasons. When leftover food, along with the excrement of each organism (with a high ammonium content), is biologically degraded, secondary chemical compounds form (nitrites and nitrates), which are very harmful to the occupants of the aquarium and must be removed. Final sterilisation of the water is required as a biological prevention measure towards the exterior of L’Aquarium.

The new AERZEN Delta Blower starts up in case of emergency, such as an electrical breakdown, and thus makes sure that the water runs out of filtration, and the fishes are provided with oxygen. The circulation of water is what generates oxygen. In addition, in an emergency, porous, pumice-like stones are put in the water to oxygenate the water. The AERZEN Delta Blower provides absolutely oil-free air according to ISO class. For the Aquarium application, it is a must: If the blower was operated with oil it would be fatal for the fishes.

Link to the video of Aerzen Iberica: http://blog.aerzen.es/puesta-en-marcha-del-delta-blower-en-el-aquarium-de-barcelona/

News from AERZEN Product Managers

On June 1, 2019, Ricardo Wehrbein took over the activities of Product Manager Delta Hybrid at AERZEN. Ricardo Wehrbein can draw on experiences as Product Manager Accessories & IoT. He also worked as an electrician for Delta Hybrid machines before studying industrial engineering, and can, therefore, rely on extensive practical experience.

Christian Reimann took over the position of Product Manager for Delta Blower and Alpha Blower on June 1, 2019. Previously, Christian Reimann was exclusively responsible for AERZEN Alpha Blowers as Product Manager. His experience as a quotation engineer for standard and modified solutions regarding blowers and compressors provides him with sound product and application knowledge.